SilverStone FT02 Installationsanleitung

MANUALFORTRESS SERIESFT02

9 9 10 Remove the hard drive tray as shown Выньте корзину для жесткого диска, как показано на рисунке. Вставьте жесткий диск в корзину и закрепите

10 11 12 Insert the completed hard drive tray back into the case (additional CP05 adapters can be purchased separately to make all SATA hard drives

11 13 14 Use screw A to secure the 2.5” hard drive to the bracket С помощью шурупа A закрепите 2,5-дюймовый жесткий диск в кронштейне. C помощью шу

12 15 16 Insert all standoffs to corresponding holes on the motherboard tray as required by your motherboard, then place the motherboard on the sta

13 17 18 After all wires and cables are connected and routed, place the side panels back onto the case and secure with thumb screws removed from st

14 Power switch and reset switch installation guide: Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector” or “System

15 Front I/O connector guideBelow are the front I/O connectors pin definition, please also check your motherboard manual to cross reference with mothe

16 1 2 Please remove 180mm fan filters as shown then remove the four 3*8 screws holding the 180mm fan bracket Снимите фильтры 180-мм вентилятора, ка

17 3 4 Remove 180mm fan bracket from the case then unscrew the eight screws holding the fan grille to the fan Выньте из корпуса кронштейн 180-мм вен

18 56Secure the radiator onto the fans as shownЗакрепите радиатор поверх вентиляторов, как показано на рисунке.Befestigen Sie den Kühler wie dargestel

1 Installation and system optimization guide: The following manual and guides were carefully prepared by the SilverStone engineering team to help yo

19 7 8 Insert fan filters back into the fan bracket, please make sure the filters are in the correct orientation Вставьте фильтры вентилятора обратн

20Component size limitationsCPU cooler height limitation 165mm Power supply length limitation:230mmThe FORTRESS FT02 was designed to accommodate overs

21 Graphic card/expansion card length limitation Motherboard size limitation FT02 can support 12” consumer level graphics cards.Graphic card length re

22 Obwohl der FORTRESS FT02 nicht zur Verwendung von Extended-ATX-Motherboards entworfen wurde, ermöglicht der Platz im Gehäuseinneren die Installatio

23 Falls der 7. Erweiterungssteckplatz genutzt wird, liegt die maximale Tiefeeines optischen Laufwerks (einschließlich Anschlüssen) bei 193 mm. Falls

24 The gap between I/O and top cover is 70mm Acceptable connector Unacceptable connector 70mm Top cover limitation

25 Recommended cooling device setup and selectionIf you are installing a tower-style CPU cooler, we recommend that the CPU fan blows upward to work

26 There are hooks behind the motherboard tray for using cable straps in routing cables. Cable routing Fan speed adjustment За лотком для материнско

27 Standard 180mm fan, fixed speed at 700rpm (100CFM) FN181 FN181-BL FM181 180mm fan with blue LEDs, fixed speed at 700rpm (100CFM) 180mm fan with

28 1 2 Please remove 180mm fan filters as shown then remove the six 3*8 screws holding the 180mm fan bracket Снимите фильтры 180-мм вентилятора, как

2 4.5mm aluminum unibody frame, 0.8mm steel body SSI CEB, ATX (maximum 12” x 11”), Micro ATX BottomTopSST-FT02B (black)SST-FT02S (silver)SST-FT02B-W (

2934Remove 180mm fan bracket from the case then unscrew the twelve screwsholding the fan grille to the fanВыньте из корпуса кронштейн 180-мм вентилято

30 An example of a GPU cooler that is filled with dust and has lost most of its cooling performance FT02’s positive air pressure design is an effecti

31 Power supply filter removal guide: Please press on the two power supply filter tabs as shown in illustration ”1”, then pull them out to remove f

32FT02ᬃᧈ667&/($5&026ᅝ㺙೼䴲ऴ⫼ⱘ6ORWवῑⱘഄᮍˈ䇋খ㗗ϟ೒˖FT02ᬃᧈ667&/($5&026ᅝ㺱೼䴲Ԩ⫼6ORWवῑⱘഄᮍ䂟গ㗗ϟ೪FT02ὀή̵ώἿଣࠪἦὝἰᦼԋἸἿṽṽṾṗṭṶṯṫṼṭṷṹṽὨᾷώᾌ̵ᾯἼࡠ৓Ἠἷἕ὏ἪẪͣἿЇ

33You can purchase additional CP05 adapters to enable SATA hard drive hot-swap. There is already one included in the case, with four more slots avail

34 E’ possible acquistare separatamente adattatori CP05 per abilitare la funzione hot-swap per gli hard disk SATA. Uno è compreso negli accessori del

September, 2009Issue date:G11210830

3SCREW BSCREW ASCREW CSCREW DRADIAOR-BKTBUNCH WIRE TIESPSU BKT2.5” HDD BKTBUNCH WIRE TIESFAN CABLEAC’97 CONNECTORSECURE 5.25" DRIVESECURE HARD DR

412Place one hand into the top rear handle hole and another hand into the recessed cable hole then pull top cover off the case evenly in the direction

6 4 4. Install PSU into the case as shown (two orientations are available in A or B), use screw C to secure the PSU 4.5. Route the PSU strap arou

7 5 6 Take the included PSU holder from the accessory box and secure it with screw C to the case Выньте из коробки с аксессуарами прилагаемый держат

8 7 8 Push the 5.25” tool-less buttons to “unlock” position,then insert an optical drive or other 5.25” device into the case and align its bezel to